A fractional horsepower motors manufacturers directory including fractional motors, fractional hp motors, electric motors, DC motors, AC motors, gear motors, permanent magnet motors, universal motors, variable speed motors, shunt motors and reversible motors.  

Information Page Links:

Featured Fractional Horsepower Motor Manufacturers

About Fractional Horsepower Motors

Fractional Horsepower Motor Terms

Fractional Horsepower Motor Associations

Fractional Horsepower Motor Resources

Trade Shows

Featured Fractional Horsepower Motor Articles

More Articles

ISO - International Organization
for Standardization

Back

About Fractional Horsepower Motors

A fractional horsepower motor is a motor, built in a frame, which has power that rates smaller than one horsepower. They can be fuel powered but most often are electric. Being categorized as a fractional hp motor can be relative to the frame size as well as the amount of fractional horsepower. The frame size of the motors is based on the standards put in place by the National Electrical Manufacturers Association (NEMA). If the frame size is a 42, 48 or 56, then it can be a fractional horsepower motor even if the horsepower exceeds one horsepower. From the 56 frame on up, motors are available in horsepowers greater than those normally associated with fractionals. For instance, 56 frame motors can go as high as 5 hp. For this reason, calling motors with two-digit frame sizes "fractionals" is technically somewhat misleading. So the way a motor is deemed “fractional” is largely dependant on the manufacturer. It is important to note that each frame size designates a particular shaft height, shaft diameter and face or base mounting hole pattern.

These motors are used in many industries and often need to be customized. They provide power and controlled motion for smaller or low horsepower needs. They are part of small surgical devices in hospitals, in internal computer fans and as part of pumps as well as many other industrial and commercial applications. The internal power configurations are varied depending on the desired use of the motor itself. They configure electrical power into rotational energy and thus actuate the devices that they are connected to.

It is important to note the main components of electrical motors in general of which fractional hp motors are a type. The components of an electric motor are the enclosure, rotor, axle or shaft, coil and field magnet. Not all electric motors contain brushes, which help conduct current. When an electric motor is brushless, a external power supply is used to get the current transferred. Brushless electric motors are actually more expensive because they last longer and have fewer issues with potential sparking from high speed operation.

When looking for a fractional horsepower motor, the following labels are important to consider: C= face mounting, G=gasoline pump motor, H=frame with larger “F” dimension, J=jet pump motor, Y=unique/special mounting dimensions and Z=shaft extension, which is not standard, but all other mounting dimensions are standard. Fractional hp motors can be either AC or DC. Each application requires a different standard of necessities for optimum motor selection and performance. Keep in mind the voltage, frequency and number of phases of power supply needed. Custom fractional horsepower is available for uncommon situations.

Fractional Horse Power Motors
Images Provided by Dumore Corporation

Featured Articles

”End Uses and End Users of Small Electric Motors”
http://www.findarticles.com/cf_0/m1094/2_35/63607835/p1/article.jhtml

Images Provided by Met Motors

Types of Fractional Horsepower Motors

• AC (alternating current) motors are either induction or synchronous. They have a current that flows in either direction, usually with electric power.
  
• DC (direct current) motors have variable speed operation capabilities with current, which flows in one direction. Often use electric power.
  
• Electric motors are motors that convert electric energy into motion using magnetism. (http://www.electric-motors.net)
  
• Gearmotors are a combination of a motor and gearhead that reduce motor speed to desired RPM’s. (http://www.speed-reducers.org)
  
• Integral-horsepower shunt motors are used when minimum speed variation requirements are necessary at constant potential with full to no load and/or constant horsepower.
  
• Multi-speed motors come in two, three or four speeds.  They have varying connections that can alter the speed at the starter, because of the way they are wound.
  
• Permanent magnet synchronous (PMR) motors have magnets in their rotor assemblies. These allow the rotor assembly to arrange itself in a line with the rotating magnetic field of the stator, which results in no slip and higher torque efficiency.
  
• Reversing motors can be AC or DC.  A typical DC motor is almost always reversible by changing the polarity of the field; an AC motor is reversed in a three-phase power motor by reversing connections of one leg and in a single phase by reversing the leads.
  
• Small electric motors, or fractional horsepower motors, have less than one horsepower of power.
  
• Synchronous motors operate up to full load at a constant speed and are often used to maintain an exact speed. The rotor speed and the rotating magnetic field speed are equal.
  
• Universal electric motors can run on either AC or DC power.
  
• Universal motors are capable of operating on both direct current and alternating current.
  
• Variable speed motors direct the rotational speed of an AC motor and can be found in many heating and cooling systems.
  
• Variable torque motors are essentially multi-speed motors whose loads have varying torque requirements along with varying speed requirements. Found in pumps and blowers.